• Contact rating (Res. load):16A 277VAC/24VDC
• Maximum switching voltage: 400VAC(NO)
• Maximum switching current: 16A
• Maximum switching power: 4700VA

• Arduino UNO Rev3 / Mega Shield compatible footprint
• Can work with both 3.3V and 5V
• Can dispaly on Chipkit UNO32 and Simplecortex as well
• Backlight : LED

• Only uses 4 Arduino pins (2,3,4,5)
• All through-hole parts for easy kit assembly
• Available in green display color only at this time

• High performance and fully static 32-bit x86 processor board
• Sensor: LSM330DLC (6-axis accelerometer & gyro)
• Communication: I2C, SPI, UART, RS485, CAN, LAN
• Digital I/O pins: 45 (11 provide 32bit PWM output)
• Memory: 128MB DDR3

• Shield for the Raspberry Pi to connect Arduino shields
• Requires no physical configuration to work with most shields
• Allows to stack and use Arduino shields over the Raspberry Pi
• Simple and inexpensive way to unite the two systems

• Low-cost robust H-bridge ''shield'' for Arduino
• Provides the ability to control up to 30A of current at up to 28V
• Supply voltage: 5V to 28V (24V max battery rating)
• Continuous output current: 13A

برد آردوینو Due یک میکروکنترلر بر پایه SAM3X8E ARM Cortex-M3 CPU از شرکت Atmel می باشد. این برد، اولین برد آردوینویی است که بر اساس میکروکنترلر با هسته ARM 32 بیتی پایه ریزی شده است.

• A small, but mighty power supply
• Designed to be as small and inconspicuous as possible
• Board has AAA battery clips but can use an input from 1.2V to 5V
• RoHS Compliant

• Dual full H-Bridge driver with PWM control
• 2Amps per motor, 24VDC maximum motor voltage
• Large high quality decoupling capacitors
• Arduino Nano is not included

• Advance MP3 decoder IC, VS1053B
• On-board audio amplifier, volume control, speaker
• Breadboard friendly, small size 3.7'' x 1.1''
• Four mounting holes for standalone application
• Arduino Nano USB Microcontroller v3 is not included

• IEEE802.3af compliant
• Low output ripple and noise
• Input voltage: 36V to 57V
• Can be used with the Arduino Ethernet shield and Arduino Ethernet

برد آردوینو Uno یک میکروکنترلر بر پایه ATmega328 می باشد . این برد 14 پین ورودی و خروجی دیجیتال (که 6 تای آن می تواند به عنوان خروجی PWM استفاده گردد)، 6 ورودی آنالوگ، یک تشدیدگر سرامیکی 16مگاهرتز (Ceramic Resonator)، یک پورت USB، یک پاورجک (ورودی منبع تغذیه)، یک ICSP header و یک دکمه ریست دارد. برد Uno شامل کلیه امکانات مورد نیاز جهت بکارگیری میکروکنترلر موجود بر روی برد می باشد. برای شروع تنها با یک کابل USB، به سـادگی برد را به کامپیوترتان متصـل کنید و یـا آن را با یـک آداپـتور AC-To-DC و یا باتری راه اندازی نمایید.

• Can be easily used with Arduino/Iteaduino for transparent wireless serial communication
• Integrates a Serial Bluetooth module
• On board PCB antenna
• Up to10m communication distance in house without obstacle

• Bluetooth microcontroller for BLE projects
• Microcontroller: Atmega328
• On-board BLE chip: TI CC2540
• Support AT command to config the BLE

• Supply: 4.5V - 35V
• Output: 1.25 - 12V
• Output current: 2A (3A peak)
• Efficiency: 90%
• Arduino compatible

• Working voltage:3.3V
• Speically designed for controlling servos
• Arduino Compatible
• Features a 12 standard servo control capbility with an Xbee socket

• Arduino input shield with two axis mini joystick
• APC220 radio data module interface and Xbee interface
• Easily stacked on top of your Arduino boards
• Comes with 4 colored push buttons

• Completely new design capable of controlling 4 relays
• Compatible with Arduino UNO Rev3
• Each Relay has its own test button
• Supply Voltage: 9V

• Easily control 2 stepper motors with only 4 digital I/Os
• Five different microstep resolutions (down to 1/16-step)
• 10 channel digital I/O & 6 channel Analog I/O addition
• Input voltage: 8-35V DC

• EFCom arduino compatible module
• Fully compatible with AVR/Arduino/ARM/FPGA
• Super capacitor power supply for the RTC
• Supply voltage range of 3.1 to 4.8V

• Supports GPS technology for satellite navigation
• Embeded high-gain SMD antennas for GPS & GSM
• controlled via AT commands
• USB/Arduino control switch
• Programmable switch for Arduino

• 4X4 key-pad shield with a 5110 Graphic LCD interface
• Can plug it on Arduino boards directly
• Can get the small development platform with keypad input and Graphic LCD display
• Version: 1.1

This is a design for an open-source prototyping shield for Arduino Mega. It has tons of cool features, to make prototyping on your Arduino easy. Some assembling and soldering is required!

Working Voltage: 5V
• Compatible with TF SD card, which is the most tiny card in the market
• Includes various applications such as data logging, audio, video, graphics
• Greatly expands the Arduino memory
• Interface: SPI

• First chip-sized Arduino compatible module
• On-board 64x48 pixel OLED
• Consist of ATmega328P and 5V & 3.3V LDO
• Arduino IDE 1.0+ compatible

• High quality MP3 shield with Arduino compatiblity
• Able to decode and play MP3 audio files from microSD card
• Stackable side headers to allow more Arduino shields to be stacked
• On board high quality 24 bits audio DAC

• MQ2 smoke detector shield for Arduino/pcDuino
• Detects the concentrations of combustible gas in air
• Measures concentrations of 300 to 10,000 ppm
• Consumes less than 150mA at 5V

• Host Interface: UART
• Working Voltage: 3.3v or 5v
• Serve for contactless communication at 13.56MHz
• Supports ISO 14443B in reader/writer mode only