چنانچه شما برد آردوینو Uno را تهیه نموده اید ، برای شروع کار این شیلد یکی از گزینه های های پیشنهادی ما می باشد، با استفاده از این شیلد به راحتی می توانید به پین های برد آردوینو دسترسی داشته باشید و به سرعت مدار خود را پیاده سازی نمایید و در نهایت با لحیم کردن قطعات مدارتان ، این شیلد نمونه سازی را تبدیل به یک شیلد کاربردی و اختصاصی نمایید.

100% brand new and high quality
This expansion board as a driver expansion board, can be used for engraving machines, 3D printers.

• Low-cost robust H-bridge ''shield'' for Arduino
• Provides the ability to control up to 30A of current at up to 28V
• Supply voltage: 5V to 28V (24V max battery rating)
• Continuous output current: 13A

• Completely new design capable of controlling 4 relays
• Compatible with Arduino UNO Rev3
• Each Relay has its own test button
• Supply Voltage: 9V

• Can be easily used with Arduino/Iteaduino for transparent wireless serial communication
• Integrates a Serial Bluetooth module
• On board PCB antenna
• Up to10m communication distance in house without obstacle

Description

• Double shield interfaces compatible with Arduino for easy cascading
• Provide maximal 500mA under 3.3V
• Full 2.54mm break out for XBee
• 3 indicator (ON/SLEEP, RSSI, ASS) LED for XBee

• Shield for the Raspberry Pi to connect Arduino shields
• Requires no physical configuration to work with most shields
• Allows to stack and use Arduino shields over the Raspberry Pi
• Simple and inexpensive way to unite the two systems

• Bluetooth microcontroller for BLE projects
• Microcontroller: Atmega328
• On-board BLE chip: TI CC2540
• Support AT command to config the BLE

• High quality MP3 shield with Arduino compatiblity
• Able to decode and play MP3 audio files from microSD card
• Stackable side headers to allow more Arduino shields to be stacked
• On board high quality 24 bits audio DAC

• Arduino input shield with two axis mini joystick
• APC220 radio data module interface and Xbee interface
• Easily stacked on top of your Arduino boards
• Comes with 4 colored push buttons

• Contact rating (Res. load):16A 277VAC/24VDC
• Maximum switching voltage: 400VAC(NO)
• Maximum switching current: 16A
• Maximum switching power: 4700VA

• Only uses 4 Arduino pins (2,3,4,5)
• All through-hole parts for easy kit assembly
• Available in green display color only at this time

• First chip-sized Arduino compatible module
• On-board 64x48 pixel OLED
• Consist of ATmega328P and 5V & 3.3V LDO
• Arduino IDE 1.0+ compatible

Easy way to give voice to your robots and projects
• Supports Chinese and English languages
• Baud rate: 4800,9600,57600,115200
• Interfaces: UART, IIC and SPI

External Power Range: 3.3V - 5.5V
• Interface: I2C and Interrupt Output
• Selectable 12/24 Hours Format
• 0.5s IIC Bus auto reset function to avoid from getting stuck

• MQ2 smoke detector shield for Arduino/pcDuino
• Detects the concentrations of combustible gas in air
• Measures concentrations of 300 to 10,000 ppm
• Consumes less than 150mA at 5V

• Arduino compatible WiFi shield V3 supporting AP+STA dual mode
• Provides UART(TTL) to IEEE802.11b/g/n wireless communication
• Transmission rate: 54Mbps - 1Mbps
• Frequency range: 2.4 - 2.497GHz

• Easily control 2 stepper motors with only 4 digital I/Os
• Five different microstep resolutions (down to 1/16-step)
• 10 channel digital I/O & 6 channel Analog I/O addition
• Input voltage: 8-35V DC

• A small, but mighty power supply
• Designed to be as small and inconspicuous as possible
• Board has AAA battery clips but can use an input from 1.2V to 5V
• RoHS Compliant

• EFCom arduino compatible module
• Fully compatible with AVR/Arduino/ARM/FPGA
• Super capacitor power supply for the RTC
• Supply voltage range of 3.1 to 4.8V

• SD card shield to add storage in Arduino project
• SD card, Micro SD card and SDHC card supportable
• On-board toggle switch to select the SD card type
• I2C header and UART header on board

• High performance and fully static 32-bit x86 processor board
• Sensor: LSM330DLC (6-axis accelerometer & gyro)
• Communication: I2C, SPI, UART, RS485, CAN, LAN
• Digital I/O pins: 45 (11 provide 32bit PWM output)
• Memory: 128MB DDR3

• Arduino UNO Rev3 / Mega Shield compatible footprint
• Can work with both 3.3V and 5V
• Can dispaly on Chipkit UNO32 and Simplecortex as well
• Backlight : LED